Top Treatments

This board-mounted top treatment is an arch-shaped (straight center with angled ends) valance featuring symmetrical pleats (shown with contrast lining)

• Board mounted, not a washable treatment
• Top finished with ¼” welt
• Optional Velcro® with no welt (only with 118” fabric)
• Self lined
• Specify short point. Long point will be 13 1⁄2″ longer.
• Return will be 3 1/2″
• Number of center box pleats will be determined by the treatment width

A board-mounted, empire-style bell swag valance

• Board mounted, not a washable treatment
• Contrast lined
• Swags are cut on the bias, unless otherwise requested
• Return will be 3 1/2″
• Specify length: 16″, 18″ or 20″
• Swag width approximately 26″
• Number of swags determined by treatment width — minimum width is 31″

This board-mounted top treatment is a tailored, box pleated valance (shown with banding on the bottom)

• Board mounted, not a washable treatment
• Self lined
• Specify length 10″ – 24″
• Pleats spaced approximately 17″ apart
• Half pleat on corner
• Return will be 3 1/2″

This rod-mounted top treatment is a sleeve (without headers) that gathers onto a rod

• 3 1⁄2″ sleeve
• 5 1⁄2″ sleeve
• Sheers will be 3X fullness
• Drapery weight fabrics will be 2.5X fullness
• Double layer (available only with 118″ fabrics) if specified

This rod-mounted top treatment is a sleeve with headers at the top and bottom that form ruffles when gathered onto the rod

• 3 1⁄2″ sleeve has 1 1⁄2″ headings on top and bottom
• 5 1⁄2″ sleeve has 2″ headings on top and bottom
• Sheers will be 3X fullness
• Drapery weight fabrics will be 2.5X fullness
• Double layer (available only with 118″ fabrics) if specified

This rod-mounted top treatment is a flat panel with a grommet top

• Length up to 24″
• Lined
• Specify grommet size and color
• Space between grommets is approximately 6″

This board-mounted top treatment is a shaped valance featuring evenly spaced kick pleats and kick pleats on the corners

• Center scallop with angled ends
• Spaces approximately 16″
• Board mounted, not a washable treatment
• Top finished with ¼” welt
• Optional Velcro® with no welt (only with 118″ fabric)
• Self lined
• Return will be 3 ½”
• Number of scallops will be determined by the treatment width
• Specify length of center scallop. Short point will be 2″ shorter than scallop. Ends will be 2″ longer than scallop

A rod-mounted swag valance with overlapping swags and cascades (shown with trim)

• Swags are cut on the bias, unless otherwise requested
• Self lined
• Velcro provided for mounting to the rod
• Number of swags determined by treatment width
• Specify swag placement
• Cascades up to 36″ long, please specify desired length

This rod-mounted top treatment is a pleated panel available with a pinch, bohemian or goblet pleat

• Length up to 24″
• Lined
• Specify pleat style
• Pinch and bohemian pleat will have a 4″ buckram
• Goblet pleat will have a 5″ buckram

A rod-mounted, pointed bell swag valance (two shown with trim over pleated panels)

• Swags are cut on the bias, unless otherwise requested
• This bell swag valance is self lined

This pouf swag valance has a relaxed top, multiple swags with tails and poufs

• 118″ fabric only
• Swags are cut on the bias
• Self lined
• Tails and poufs attached
• Tail length up to 36″, please specify
• Ring mount, please specify ring-to-ring measurement
• Minimum width is 48″ — Maximum width is 144″
• Number of swags determined by treatment width

This pouf swag valance has a relaxed top, single swag with tails and poufs

• 118″ fabric only
• Swags are cut on the bias
• Self lined
• Tails and poufs attached
• Tail length up to 36″, please specify
• Ring mount, please specify ring-to-ring measurement
• Minimum width is 36″ — Maximum width is 120″

This rod-mounted top treatment is a flat panel with soft top (no buckram)—micro welt on top edge

• Length up to 24″
• Lined
• Micro welt covered in same fabric
• Clip rings are suggested for use on the top (not included)
• The number of clip rings used is a design feature to be determined by the decorator

This rod-mounted top treatment has a top-sewn pocket (with or without headers) that gathers onto a rod (shown with trim)

• Length up to 24″
• Lined
• Specify pocket size
• Specify header size (if desired)

A rod-mounted, rounded swag valance with no cascades (two shown over pleated panels)

• Swags are cut on the bias, unless otherwise requested
• This swag valance is self lined

A rod-mounted, rounded swag valance with one (left OR right) cascade (two shown with contrast lining over pleated panels)

• Swags are cut on the bias, unless otherwise requested
• Self lined
• One cascade (left OR right)

This board-mounted top treatment is a scallop-shaped valance featuring pleated jabots (shown with contrast lining)

• Board mounted, not a washable treatment
• Top finished with 1⁄2″ welt
• Optional Velcro® with no welt (only with 118″ fabric)
• Self lined
• Space between jabots is approximately 15″
• Specify length of scallops; jabots will be 2″ shorter than scallops
• Return will be 3 1/2″

This pouf swag valance has a straight top, multiple swags with tails and poufs

• 118″ fabric only
• Swags are cut on the bias
• Self lined
• Tails and poufs attached
• Tail length up to 36″, please specify
• Ring mount, please specify ring-to-ring measurement
• Minimum width is 48″ — Maximum width is 144″
• Number of swags determined by treatment width

This pouf swag valance has a straight top, single swag with tails and poufs

• 118″ fabric only
• Swags are cut on the bias
• Self lined
• Tails and poufs attached
• Tail length up to 36″, please specify
• Ring mount, please specify ring-to-ring measurement
• Minimum width is 36″ — Maximum width is 120″
• Number of swags determined by treatment width

A traditional board-mounted swag valance (shown with banding on the bottom)

• Board mounted, not a washable treatment
• Cascades contrast lined
• Swags are cut on the bias, unless otherwise requested
• Swag lined with standard lining
• Swag length is 18″
• Cascades up to 36″
• Return will be 3 1/2″
• Number of swags determined by treatment width—minimum width is 30″
• For multiple swags, please specify swag placement